FLEXISPOT EN1 One-Piece Standing Desk, 48″x24″ Seamless Desktop Electric Height Adjustable for Home Office, Study Rooms & Multi-Device Workstations, Black

Solid desk, great value for the money
I’ve used high-end electric desks at work, and since you typically get what you pay for, I was a bit wary of buying one for home that was so relatively inexpensive. But overall the reviews were positive enough (especially regarding customer service) and there were some good tips regarding assembly, so I figured it was worth the risk.Both boxes arrived with the contents in perfect condition: the boxes used very thick, heavy cardboard, and the corner protectors on the desktop were made of a very dense rubber. I’ve unpacked a lot of furniture (assembling desks for classrooms and computer labs), and the packaging for this desk puts many so-called “commercial” products to shame. Any damage that might occur would be due to careless shipping and handling – not how the factory packed it.Assembling the desk was straightforward enough, although I’ve put together enough of this sort of furniture over the years that there weren’t any surprises. Just take your time, follow the steps, and you’ll be fine. This can be assembled by one person, but a second set of hands will make things easier.All of the pre-drilled holes lined up where they were supposed to. One assembly tip: line up one of the end holes in a leg with its corresponding hole in the desktop, and drop a thin nail into the hole to give it something to pivot around. Then with that hole aligned, line up each of the other holes, again dropping a thin nail into each one until they’re all aligned. Then drive the screws, replacing each nail, one at a time. No guesswork, no misaligned screws, no do-overs.The only two pilot holes I had to add were for the center crossbar, so you will need a drill and a small bit (a hand drill or pin vise would work for this). For driving all of the screws I used a hand screwdriver, so I wouldn’t run the risk of stripping out the particle board.Everything went together very nicely. There were no stripped threads or alignment issues. Overall, I felt the quality of the desk and and the fit and finish of the parts were excellent and exceeded my expectations.The motor operates pretty quietly, and raises and lowers the desk just fine, even with a bunch of stuff piled on top of it (I don’t plan on testing what its limits are – it holds what I need). I had an error message pop up on the controller once when I attempted to recall a saved height, but unplugging the desk from power and reconnecting it resolved that. No issues since.The desk is solid and stable. At its higher settings it will sway a little bit when leaned on, but that’s just physics at work – if you need something that’s really solid at full height, get something with four legs instead of two.The only (minor) gripe that I have is that the cords could be a bit longer: the one for the control panel so you could reposition it if you needed to; and the power cord which barely reaches the width of the desk.I’m very pleased with this purchase. It met my budget, and exceeded my expectations. It’s a good-looking, solid, quality desk. Hopefully it’ll hold up over time – but so far, so good!

Stable and good width
Good price. It was easy to set up and it feels stable when im using the motor and adjusting the height.

Sturdy and nice looking desk
Desk was on sale and bought the Maple 55 inch.Ships in two shipments, the top and the motorized bottom.Not too bad to put together. Instructions are clear, however it does say to adjust the crossbar early on in instructions. But you aren’t going to be able to do that until you are mounting to the top so you can line the holes up. So I would just ignore that step or make it a little wider to give you some working room.Once it comes time to mount the top do one screw top/bottom on one side. Then loosen the crossbar and transmission rod and extend until until you lined up the other side with the holes. Once all screwed in tighten the rod and crossbar.One thing I think would have helped was a guide on where the center of the crossbar extension was so you could extend it in a balanced way. I just eyeballed it. Most the weight is going to go to the legs anyway so not concerned.As far as predrilled holes go, they lined up perfectly on left/right side. There is no predrilled holes for the crossbar however you don’t need a drill the wood is soft enough to just screw into with a bit of force.Theres also no predrilled hole for the back of the up/down switch but again not a problem. Theres plenty of holes to position the switch where you want (though it must be on the right side of the desk near the motor since the cords aren’t that long).One other nitpick is the bracket that holds the power adapter doesn’t lock into place. It just slides around freely. Being nitpicky though its not a functional problem.All pieces were there. The top looks really nice but it isn’t heavy enough to be solid maple. But all put together the desk has good weight and very sturdy. Motor works well, I actually didn’t even buy it for being a standing desk so thats a bonus. It was a good price even if it didn’t have that feature.Pros:-sturdy and good weight to it-motor is enough to do the job.-not bad to put together. No frustrating moments. Takes about an hour. Only need a sturdy philips screwdriver no drill needed.-top is one solid piece-its deep! Most cheaper desks are 20-24 inches. 28 inches is a very noticeable difference.-good price-the desk gets very tall, I was surprised. I am 6’2 and it got more than tall enough for me.Cons-couple of nitpicks about instructionsWell see how long it lasts but so far am satisfied.

I checked reviews before buying this desk, because it is a lot cheaper than I can get locally and I wondered about the quality. I agree with reviewers who like it.It was pretty easy to assemble, and the instructions are a lot better than I’d get from Ikea. I didn’t attach the hooks because I don’t need them.I suggest testing the mechanism before you install the baffle plates and turn the desk the right way up. I didn’t, and had to turn it over again and remove the baffle plates to fix the mechanism, because I had not pushed the rod properly into the motor and only one leg was moving.All in all, a nice looking and well built riser desk at a good price.

Me gustó que de verdad cumple con la función qué promete, llevo usándola unas semanas y de verdad me encantó.